New One Man Boat

yoderjac

Well-Known Member
I'm preparing for the next step in retirement. Soon our retirement home will be built and I'll have a lot more free time (I hope). When I was young, I was an avid fisherman. When I was 10, I graduated from the spinning rod to a flyrod and began flyfishing for trout with my dad and started tying my own flies. In the western PA, most of the trout fishing was put-and-take in stocked streams. When I went to Penn State, I fell in love with trout fishing. I couldn't drive 25 minutes in any direction without crossing one of the top limestone streams in the east!

When I eventually moved to Northern VA, I tried to take up warm water fishing again. I got a bass boat and fished the Potomac and Lake Anna for bass. There were no limestone streams and even the freestone streams cold enough for trout were several hours drive through traffic. I eventually found Quantico MCB for hunting. I eventually replaced my spring trout fishing with spring gobbler hunting there. Our use of the bass boat became more and more infrequent and I eventually I gave it to my brother-in-law and sister-in-law who had kids of the right age for boating. I kind of gave up fishing after that and focused on hunting and wildlife management.

Well, now that I'm retired, I think I'll take it up again. Cold water trout streams are still a bit of a drive up into the mountains, but there are a lot of small warm water rivers near by with smallmouth bass. My plan is to start with smallmouth nearby and then eventually see if flyfishing is worth the drive.

To that end, some friends invited me on a kayaking float on the Rivanna river nearby. Most of my fishing tackle had been given away over time, so I ran to Walmart and grabbed a $20 ultra-lite rod and reel combo and a handfull of lures. I struggled with the kayak. My back and hips were quite uncomfortable in that position. I struggled paddling against the current. I eventually fell behind the group. I could not fish while trying to control the kayak either. I eventually found eddies where I could beach the end of the kayak and fish. I loved fishing again. I caught a few smallmouth of no size to speak of, but I got the bug again!

So, I just ordered a on man raft with a frame. It is an NRS Approach 100. It is small enough that I should be able to carry it in the bed of my pickup. With a cart, I should be able to handle it myself. I ordered a Minn Kota Edge bow mount foot controlled trolling motor. I'll need to modify the frame to mount the trolling motor bracket. I ordered a Humminbird Helix DI GPS G3 fish finder for it as well. I also ordered a 10lb Tornado Anchor for it. I'll probably build a cart for it myself. I've also ordered a good rod and reel for smallmouth. The reel is a Shimano Vanford FA 2500HG with some flurocarbon line. The rod is a St. Crois Physyx series 6' 3" medium light extra fast. I was lucky and caught a 4th of July sale on the rod and reel and some lures.

It will probably be a couple weeks until all the stuff arrives and I can get it put together. I'll post some pictures once it arrives and update this thread as the new adventure unfolds.
 
Much like you. Last summer I had 7 years of EQIP contract that I had to finish in one year. I told myself, next summer I'll go fishing. This summer I have 50 tulip poplar logs laying on the ground, next summer, I'll go fishing. I would like your new set up, good luck.

G
 
Sounds fun! We run a Nucanoe with a 2.5hp Yamaha 4 stroke to get more range. It’s great for inshore fishing in Va.

5dfd2baa59d19addde15e1098374ef44.jpg



Sent from my iPhone using Tapatalk
 
Much like you. Last summer I had 7 years of EQIP contract that I had to finish in one year. I told myself, next summer I'll go fishing. This summer I have 50 tulip poplar logs laying on the ground, next summer, I'll go fishing. I would like your new set up, good luck.

G
I completely understand. I tend to over analyze things, Often by the time I'm ready to pull the trigger on something like this, something else has come up and I end up postponing till next year. This time, I just through caution into the wind, and pulled the trigger. I'm sure it will take a few weeks for me to get things set up.
 
Sounds fun! We run a Nucanoe with a 2.5hp Yamaha 4 stroke to get more range. It’s great for inshore fishing in Va.

5dfd2baa59d19addde15e1098374ef44.jpg



Sent from my iPhone using Tapatalk
Sounds like you have a nice setup. I thought about a gas motor and opted against it. There are lots of places that are electric motors only around. Also, parts of the Rivanna are pretty shallow at times. With a quick depth adjust on an electric, I could raise it almost out of the water and still operate it. Besides I'm retired and don't need to get anywhere fast...😊
 
The boat was supposed to arrive yesterday according to Fedex, but it was evidently delayed and showed up early this afternoon. It came in 3 boxes, a large rectangular box with the raft in it, a long flat box with the long rails and pump in it, and a smaller rectangular box with the seat. Here are the boxes with the seat and rails:

f4862dba-61ef-40a1-ab7a-05b53e5fcd12.jpg


dd047b5f-0661-4381-bb4b-07a9fd5a8fda.jpg


The electric inflator pump I bought from Amazon was advertised to have the correct connector but it did not. I spent a lot of time trying to adapt it. I finally decided just to hold the connector against the valves in the boat which was good enough for stage 1 of the pump. Once pressure started to build, I switched to the NRS Hand Pump that came with it. Here is the inflated raft:

f91e4003-e775-475d-868c-ee7af0366174.jpg


Once the raft was inflated, I started watching the assembly video and following along with it. Here is the video for anyone interested:
When I got to the seat, I was shocked how heavy it was when I pulled it from the box. No wonder, it was full of hardware:

e2e530b6-02a6-45bb-b0da-2932fedaffff.jpg


Things went well until I got to the oarlocks. Rather than slipping the T-nuts in from the ends, they show how to drop them in for the oarlock install. It worked as shown on one rail, but not the other. The rail must be a little out of spec. The rail that works has an opening of 5.8-5.9mm. The one that doesn't is 5.7-5.8mm. Here is a picture of how the t-nuts hangs when inserted from the side:

41e45658-3471-48ee-af4a-b6bede72b62c.jpg


If I was only interested in assembling the basic boat, I could work around this by changing the installation order, but I plan to add some Yak Attack accessories to the rail, and I don't want to have to disassemble the boat to add them.

I called them and they had me send an email to their service department with the haul number and they would send me a new rail. I did that. My state requires any boat with a motor, even trolling, to be registered. I'll need the certificate of origin for that. It did not come with the boat, so when I called them I asked about it and they said they would send that to me as well.

So, for now, the project is on hold until I get the new rail.
 
Back
Top